[Jukebox-list] Visit from Georgia

[Jackie]

J.C.
what do you do there at the Game Room?    what are the hours of the PA Game 
Room event?  That is probably about a 2-3 hr. drive from my house to PA, not 
far from my Daughter in East Berlin, PA.   Of course it is fine if you come 
by, you almost have to pass by my house!!

As for the microswitch, I am not sure where it is, I will have to look in 
the manual, but the mech does not stop, it just plows into the pin and gets 
hung up on it.  There are a couple that are bent because of it.  Looks like 
that was an issue before I picked it up.  I haven't let it get hung up on 
it, I turn off the machine and cancel it manually right before it hits the 
pin.  I just want to watch it work..............ha! for a moment or two, lol 
What makesthe mech stop when it hits the pin?  That's what I think is not 
working.
Jackie

----- Original Message ----- 
From: <Jjmscf at aol.com>
To: <jukebox-list at lists.netlojix.com>
Cc: <Jjmscf at aol.com>
Sent: Sunday, October 01, 2006 5:02 PM
Subject: Re: [Jukebox-list] Visit from Georgia


>
> The PA Game room show is from October 20-22. I will be going on Sunday,my
> only day off from work.
>
> As for your 2410 I wonder about the carriage switch in the mechanism.  it 
> is
> a microswitch and they go bad. It should  be closed when it stops on  the 
> pin.
> Check it with your meter.It should show zero ohms or very close when
> closed.If not it's no good. It activates a reversing relay underneath 
> that should
> reverse the motor direction to start the transfer cycle.This is all 
> assuming
> the 2410 mechanism is the same as the 2510. The 2510 did that  once so 
> it's
> microswitch may be getting flaky too.
>
> J.C.
>
>
>
> In a message dated 10/1/2006 3:20:50 P.M. Eastern Standard Time,
> etreble7 at comcast.net writes:
>
>>Hi  J.C.,
>>I am 15 min. from Annapolis, off Rt. 450.  It would be great  to meet you,
>>you are always welcome!  When is that?
>
>>As  far as the 2410 working, I did not ask Roy to work on my machine.  He
> was
>>just stopping by to drop off a part and to meet me and my Jukeboxes,  LOL 
>>I
>>will have to work out the 2410 myself and with the help of  the list.  He
> did
>>offer to take it back to Georgia and do a  "make-over" which was a great
>>offer but I was short the $$ to take him  up on it.
>
>>I am hopeful on the repairs though, if I pull a pin, it  rotates but runs
>>into the pulled pin and does not stop or cancel the  pin.  I have to turn 
>>it
>>off quickly and manually pull back the  ??? (have to look up the name of
> that
>>part) and cancel the pin  manually.  That is better than no action at 
>>all!!
>>I put on new  motor mounts and put on the new turntable motor belt, yea!!!
> I
>>really don't think there is "that" much wrong with the 2410, but for  me
> it's
>>like climbing Mt. Everest!
>
>>Please feel free to stop  by, contact me off list for directions and phone
> #,
>>would love to see  you.
>>Jackie
>
>
>
>
> _______________________________________________
> Jukebox-list mailing list
> Jukebox-list at lists.netlojix.com
> http://lists.netlojix.com/mailman/listinfo/jukebox-list